How to Use a Free Cable TV Router to Make Your Own RCN Cable TV Box and Free Roku TV box

Cable modems are pretty awesome and are a staple of almost every modern home.

And there’s a huge community of people out there who are still running them in their homes.

The best part is that you can use a cable modem to get your own remote control, so that you don’t have to buy a whole new router or set up an internet connection.

Let’s take a look at how to set up a cable modems router and a Roku box.

Step 1: Connect a cable internet cable modemYou can use any cable modem you want.

You just need to have an internet service provider that offers a good internet connection (and not just a few gigs a month).

The best thing about a cable TV box is that it can connect to any internet provider and you don-t need to buy an extra router or install any special software to make your own internet connection, which would cost a lot of money.

Step 2: Create a Raspberry Pi 2 or Raspberry Pi 3 from scratchThe easiest way to create a cable box is to use an old computer, but you can also use a Raspberry PI.

These are basically tiny computers that can be used to build a cable home theater box.

We’ll use a cheap computer and a Raspberry pi for this tutorial.

We will start with the Raspberry Pi, since it’s cheap, easy to install, and has a nice GPIO pins for making and controlling the box.

You can also buy a Raspberry computer for less than $30.

Here’s the basic idea of what you need to get started:You’ll need an internet cable box or cable modemIf you don, you’ll need to purchase a cable router or a router with a cable connection.

You’ll also need a Pi, because the internet cable can be a bit difficult to connect to when you’re using a Raspberry.

Step 3: Make a basic Raspberry Pi computerStep 4: Connect it to the internetStep 5: Create the cable modemStep 6: Set it upStep 7: Create your remote controlYou need a remote control to turn the Raspberry PI on and off, to change the channel of the TV or to set the channel to whatever you want to watch.

For this tutorial, we’ll use the remote control on the Pi.

This can be easily installed on the Raspberry pi itself, but there are a few ways to get a Raspberry remote control onto the Pi without having to buy one.

You could buy a cheap remote control kit like this one for $5, or you could make your remote by downloading and using the Remote Control app from Amazon.

The Raspberry Pi is not an official Raspberry Pi hardware, so if you want the remote, you’re going to have to make one yourself.

We don’t recommend this option.

Step 8: Install the remotecontrol appOn your Raspberry Pi’s menu bar, you should see the Remote control app.

Go to Settings > Applications and let the RemoteControl app launch.

Step 9: Set the channelTo turn on the TV, you can set the TV channel to “Roku”.

To change the Roku channel, you need the Remote Controller app on the same Raspberry Pi.

Step 10: Change the channelWhen you’re done, press the Power button to go back to your home screen.

You should see a small icon in the top left corner of your screen, and the Roku button in the bottom right.

If you didn’t see the Roku icon in your home’s menu, check your internet connection and make sure that the Roku app is enabled.

Step 11: Connect the remoteTo connect the remote to the Pi, press and hold the Power key while the remote is on the screen.

Press and hold it again when you want it to connect.

Step 12: Make your cable modemNow that you have the RaspberryPi connected to the TV (which is now your TV), you need a cable to run the TV box.

The easiest way is to make a cheap cable modem.

We’re going with the cheapest, but if you don or want to buy, check out this guide.

Step 13: Connect your cable cable modemTo connect your cable modem to the RaspberryPI, you will need to connect the cable cable.

It’s a bit tricky, but not too bad.

You don’t need to worry about setting up your RaspberryPi to have the right port.

If your modem supports ethernet, you just need one cable.

Step 14: Connect everything back togetherStep 15: Enjoy!

Now that everything is working, you could just as easily connect your RaspberryPI to your TV as you would to a computer.

If it’s a RaspberryPi, you won’t need any extra software to get the box connected to your television.

The Roku app works with almost any video app that supports streaming.

For more information about using RaspberryPI-based devices with your TV, check this out.

Step 16: Install RaspberryPi softwareOn your computer, open the